share prosedure apabila check engine menyala / rpm naik turun setelah tune up Grand Livina {515635}


 http://otodiy.blogspot.com 
1. ECU Resetting Procedures

Timing is extremely critical. If it is NOT DONE within the specify time, the ECU will not reset and the Check Engine Light (CEL) will continue to remain ON. A stop watch or an analog clock with a second’s needle will be useful.

Operations Procedures

1. Confirm that accelerator pedal is fully released, turn ignition switch “ON” and wait 3 seconds.
2. Repeat the following steps (2a and 2b) procedures quickly five times within 5 seconds.
2a. Fully depress the accelerator pedal (HARD).
2b. Fully release the accelerator pedal.
3. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 10 seconds until the CEL starts blinking.
4. Fully release the accelerator pedal (while the CEL is still blinking)
5. Wait about 10 second.
6. Fully depress the accelerator pedal and keep it for more than 10 seconds.
7. Fully release the accelerator pedal (The CEL light will continue to blink).
8. Turn ignition switch to “OFF” position and now you can start the car. The CEL light should be gone.
If the CEL light continues to remain ON, repeat the above steps. Timing is EXTREMELY critical to resetting the ECU.

Edit: Added the "Easy Method" for ECU Reset
The Easy Method:

After experimenting with different timing, and reading posts by other members, I've come up with a condensed method of doing this reset. This method works EVERY time, even w/o a stopwatch. I've used this method successfully a dozen times, or so, now w/o a watch. After a few times, you won't need a watch or instructions. You'll get so darn good at it, you'll find yourself doing it while waiting at a traffic light.

Timing is not as critical with this method...no stop watch needed. Just count in your head...one-one thousand, two-one thousand, etc, or use stop watch. The most critical step is step #3....wait 10 sec, instead of 7.

1. Ignition "ON", count to 3.
2. Depress/Release pedal 5 times...hard and fast.
3. Count to 10 (not 7!) and fully depress pedal
4. Count to 12 (SES should be blinking), release pedal
5. Count to 10, depress pedal
6. Count to 10, release pedal.
7. Turn off ignition, then start engine. Done!


2. Accelerator Pedal Release Position Learning

Operation Procedure

1. Make sure that the accelerator pedal is fully released.
2. Turn ignition switch “ON” and wait at least 2 seconds.
3. Turn ignition switch “OFF” wait at least 10 seconds.
4. Turn ignition switch “ON” and wait at least 2 seconds.
5. Turn ignition switch “OFF” wait at least 10 seconds.

3. Throttle Valve Closed Position Learning

Operation Procedures

1. Make sure that accelerator pedal is fully released.
2. Turn ignition switch is “ON”.
3. Turn ignition switch is “OFF” wait at least 10 seconds.
Make sure that the throttle valve moves during above 10 seconds by confirming the operating sound.


4. Idle Air Volume Learning (Throttle Position Learning)

Preparation

Before performing Idle Air Volume Learning, make sure that all of the following conditions are satisfied. Learning will be cancelled if any of the following conditions are missed for even a moment.

Battery voltage: More than 12.9V (At idle)
Engine coolant temperature: 70 - 100 C (158 - 212 F)
Park/neutral position (PNP) switch: ON (Shifter in Park or Neutral)
Electric load switch: OFF (Air conditioner, headlamp, rear window defogger)
Steering wheel: Neutral (Straight-ahead position)
Vehicle speed: Stopped
Transmission: Warmed-up (Drive vehicle for 10 minutes.)


It is better to count the time accurately with a clock.

Operation Procedures

1. Perform “Accelerator Pedal Released Position Learning”.
2. Perform “Throttle Valve Closed Position Learning”.
3. Start engine and warm it up to normal operating temperature.
4. Turn ignition switch “OFF” and wait at least 10 seconds.
5. Confirm that accelerator pedal is fully released, turn ignition switch “ON” and wait 3 seconds.
6. Repeat the following (steps 7a, 7b) procedures quickly five times within 5 seconds.
7a. Fully depress the accelerator pedal (HARD)
7b. Fully release the accelerator pedal.
8. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 20 seconds until the Check Engine Light (CEL) stops blinking and turned ON.
9. Fully release the accelerator pedal within 3 seconds after the CEL is ON.
10. Start engine and let it idle.
11. Wait 20 seconds.
12. Rev up the engine two or three times and make sure the idle speed and ignition timing are within the specifications. 


Lakuin step 1 -4. Saat injak pedal gas 5x, pastiin ngga kehalang karpet, kalo pedal ga ketekan full ngga bakal bisa, dan timing harus pas.

Kalo lampu check engine ngga ngedip berarti timingnya belum pas...coba aja terus


by 515635
sumber : kaskus KLIK

Comments

Post a Comment

most read in a week

DIY : Bikin label fungsi fuse dan relay Aerio / Next G

Image
Gambar 1 - Main Fuse Box hanya kode saja Bikin label yuk buat kasi keterangan fungsi dari Fuse dan Relay yang ada di ruang mesin karena hanya ada keterangan Ampere dari Fuse dan kode Relay saja tanpa ada keterangan jelas mengenai fungsi dan sirkuit apa yang dilindungi. Pada user manual terdapat penjelasan mengenai fungsinya tetapi tidak ada kejelasan secara lengkap untuk fungsi-fungsi relay, selain itu dengan adanya label petunjuk singkat pada ruang mesin membuat praktis bila melakukan pengecekan apalagi di kala darurat. Gambar 2 - Label Main Fuse Box - balik dan sejajarkan saja untuk baca
Read more

Ganti steering rack Ertiga dengan merk Heiker {Muhammad Rivaldi}

Image
gambar 1 otodiy.blogspot.com #Sharing Baru ganti Racksteer assy merk Heiker. Build qualitynya oke punya nih.. bootnya bahan plastic rubber lebih kuat dan awet, casingnya semi-polished, dan kata sellernya sih untuk internal dalemnya (rack and pinion) nya udah anti karat juga jadi aman kalo kemasukan air. Saya sempet bandingin build qualitynya dengan Racksteer bawaan ertiga (merk sona) kurang lebih sama.. cuman entah kenapa rasanya si Heiker ini lebih solid qualitynya, tapi untuk cover as pinion atas saran saya pake bawaan ertiga aja karena plastic dan foam sealnya lebih bagus daripada punya heiker ini. Kalau melihat dari segi harga sih menurut saya lebih worth ini dibanding racksteer assy original (1.4 jt vs 6 jt 😂). Tapi untuk durabilitas? Well see dia tahan berapa lama.. 😁.
Read more

DIY : Test pasang Camera Mundur di Head Unit Orisinil Innova type G

Image
 gambar 1 - Camera Mundur nampak pada Fujitsu TEN bawaan Innova http://otodiy.blogspot.com Newbie masih berencana aja untuk pasang camera mundur di Grand New Kijang Innova tipe G, kebetulan ada camera copotan sebelum dipasang di mobil lain, maka newbie pingin testing dulu di Innova. Berbekal dari panduan pasang camera mundur di Innova tipe V , dan hasil browsing wiring diagram Fujitsu Ten di internet , dan hasil coba lepas Head Unit sebelumnya , maka newbie lanjutkan testing.
Read more

Socket Connector / Wiring Diagram Head Unit Fujitsu Ten

Image
 gambar 1 - Socket Connector http://otodiy.blogspot.com Masih penasaran dengan kabel untuk Camera Mundur biar bisa dipasang di Grand New Kijang Innova type G. Biarpun sudah membaca cara pasang camera mundur di Innova type V , tapi karena Head Unitnya beda tipe dengan Innova type G , biarpun sama-sama merk Fujitsu Ten, apalagi di panduan masih ragu mana Video IN plus dan groundnya, maka newbie coba browsing-browsing lagi buat nambah referensi. Dan dari google ketemu gambar-gambar berikut ini, meski kenyataannya tetap ada beda yah, but enjoy..... and do at your own risk....
Read more