DIY : {lacquer} Cara reset ECU Livina
sumber : kaskus
by 515635
Edit: Added the "Easy Method" for ECU Reset
The Easy Method:
After experimenting with different timing, and reading posts by other members, I've come up with a condensed method of doing this reset. This method works EVERY time, even w/o a stopwatch. I've used this method successfully a dozen times, or so, now w/o a watch. After a few times, you won't need a watch or instructions. You'll get so darn good at it, you'll find yourself doing it while waiting at a traffic light.
Timing is not as critical with this method...no stop watch needed. Just count in your head...one-one thousand, two-one thousand, etc, or use stop watch. The most critical step is step #3....wait 10 sec, instead of 7.
1. Ignition "ON", count to 3.
2. Depress/Release pedal 5 times...hard and fast.
3. Count to 10 (not 7!) and fully depress pedal
4. Count to 12 (SES should be blinking), release pedal
5. Count to 10, depress pedal
6. Count to 10, release pedal.
7. Turn off ignition, then start engine. Done!
Cara Reset ECU Manual :
Instructions :
Step 1 Confirm that accelerator pedal is fully released, turn ignition switch ON (NOT start) and wait 3 seconds.
Step 2 Repeat the following steps procedures quickly five times within 5 seconds.
Fully depress the accelerator pedal (HARD).
Fully release the accelerator pedal.
Step 3 Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 10 seconds until the CEL starts blinking.
Step 4 Fully release the accelerator pedal (while the CEL is still blinking)
Step 5 Wait about 10 seconds.
Step 6 Fully depress the accelerator pedal and keep it for more than 10 seconds.
Step 7 Fully release the accelerator pedal (The CEL light will continue to blink).
Step 8 Turn ignition switch to OFF position and now you can start the car.
The CEL light should be gone. If the CEL light continues to remain ON, repeat the above steps.
Remember, timing is EXTREMELY critical to resetting the ECU
by lacquerInstructions :
Step 1 Confirm that accelerator pedal is fully released, turn ignition switch ON (NOT start) and wait 3 seconds.
Step 2 Repeat the following steps procedures quickly five times within 5 seconds.
Fully depress the accelerator pedal (HARD).
Fully release the accelerator pedal.
Step 3 Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 10 seconds until the CEL starts blinking.
Step 4 Fully release the accelerator pedal (while the CEL is still blinking)
Step 5 Wait about 10 seconds.
Step 6 Fully depress the accelerator pedal and keep it for more than 10 seconds.
Step 7 Fully release the accelerator pedal (The CEL light will continue to blink).
Step 8 Turn ignition switch to OFF position and now you can start the car.
The CEL light should be gone. If the CEL light continues to remain ON, repeat the above steps.
Remember, timing is EXTREMELY critical to resetting the ECU
by 515635
Edit: Added the "Easy Method" for ECU Reset
The Easy Method:
After experimenting with different timing, and reading posts by other members, I've come up with a condensed method of doing this reset. This method works EVERY time, even w/o a stopwatch. I've used this method successfully a dozen times, or so, now w/o a watch. After a few times, you won't need a watch or instructions. You'll get so darn good at it, you'll find yourself doing it while waiting at a traffic light.
Timing is not as critical with this method...no stop watch needed. Just count in your head...one-one thousand, two-one thousand, etc, or use stop watch. The most critical step is step #3....wait 10 sec, instead of 7.
1. Ignition "ON", count to 3.
2. Depress/Release pedal 5 times...hard and fast.
3. Count to 10 (not 7!) and fully depress pedal
4. Count to 12 (SES should be blinking), release pedal
5. Count to 10, depress pedal
6. Count to 10, release pedal.
7. Turn off ignition, then start engine. Done!
INI RESET ECU BUAT RESET APA YA?? APAKAH BISA MERESET TIMING? MKSDNYA YG SEBELUMNYA PAKE SCANNER DI MUNDURIN DGN DIRESET AKAN BALIK LAGI
ReplyDeleteSetauku ada automatic retard timing, ini yang kereset.
ReplyDeleteTrus ada juga DCT Error Code ini juga bisa direset
Tapi kalau hasil settingan yang dimundurin pakai Scanner saya kurang tau pastinya, coba kontak ke forum Nissan Grand Livina saja untuk jelasnya
regards,
singachu